关于CEA混凝土膨胀剂的若干技术问题--与游宝坤同志讨论

作者阐述了CEA膨胀剂混凝土的膨胀量较大，干缩小，抗裂性能良好的特性，CEA与粉煤灰掺用提高强度，改善界面过渡层的性质，提高耐久性；CEA混凝土无Ca（OH）2溶出问题。文中列出GBJ119应用技术规范，说明CEA可用于防水工程。     

电解法烟道气二氧化硫在线监测系统的设计

介绍了一种烟道气中SO2在线检测系统，该系统可以实现24h不间断地监测烟道气中SO2的体积分数和质量浓度，同时将信息经网络传送给环保有关部门，具有一定的新颖性、可靠性、准确性。     

Resilient metal spring network silicone-matrix composite for separable interconnections

Resilient metal spring silicone-matrix conducting composites for separable interconnections in electronics were fabricated by the impregnation of silicone into a preform comprising randomly oriented C-shaped Cu-Be springs and a small proportion of Sn-Pb solder, which served to connect the springs at some of their intersections. Composites containing 6.1-9.8 vol.% total filler exhibited volume electrical resistivity 0.5-1.0 mΩ.cm and contact resistivity (with copper) 11-17 mΩ.cm². A compressive stress of about 30 kPa was needed for the low contact resistivity to be reached. The volume 17-26% and the contact resistivity increased by 5% after heating in air at 130-150°C for seven days. Composites containing <9 vol.% total filler showed no stress relaxation for seven days at 6.0% strain.     

结构参量对脉冲高斯光束布拉格衍射特性的影响

利用二维耦合波理论,研究了体光栅对时间和空间都为高斯型分布的脉冲激光光束的衍射性质,得到了衍射和透射光振幅的解析表达式.讨论了体光栅的结构参量对衍射光束的空间和频谱强度分布以及衍射效率的影响.结果表明,体光栅的波长选择带宽和衍射光束带宽随着结构参量的增大而增大,衍射效率随着入射脉冲时间宽度的增大而增大,并趋于定值,结构参量值越小,达到饱和的速度越慢,饱和值越大.     

蒸发式冷凝在制冷工艺上的应用

分析对比制冷工艺中几种冷凝方式，指出发展蒸发式冷凝技术对制冷系统节能的重要意义；通过分析蒸发式冷凝的换热机理，在试验和实践的基础上讨论了影响蒸发式冷凝器性能的几个重要因素。     

热轧带钢连续冷却过程中相变体积分数的计算

基于相变动力学原理 ,在充分考虑变形对相变影响的情况下研究了奥氏体向铁素体、珠光体和贝氏体相变的动力学。探索了热轧带钢连续冷却过程中相变体积分数的计算方法。用此方法进行的计算机模拟与实验结果相当吻合。     

Phase equilibria of quasi-binary systems consisting of multicomponent polymers 1 and 2. IV: Poly(ethylene oxide)/poly(propylene oxide) systems

To confirm the reliability of the theory of phase equibria of multicomponent polymer 1/multicomponent polymer 2 systems (i.e. quasi-binary systems) and the method of computer experiment based on this theory (Brit. Polym. J., 23 (1990)285; 23 (1990)299; Polym. Int., 29 (1992)219), could point curves (CPC), two-phase volume ratios ( R ) and critical solution points (CSP) have been determined experimentally for the quasi-binary mixtures of poly(ethylene oxide) (M¯_w = 647, M¯_w/M¯_n = 1.15; M¯_w and M¯_n, the weight-average and numberaverage molecular weights, respectively) and poly(propylene oxide) (M¯_w = 2028, M¯_w/M¯_n = 1.08; and M_w = 2987, M_w/M_n = 1.13). The hydroxyl end groups of both polymers were methoxylated in advance by the Cooper & Booth method (Polymer, 18 (1977)164). The thermodynamic interaction parameter between both polymers, χ₁₂, and the concentration dependence parameters for the above quasi-binary systems were determined by the method proposed in a previous paper (Brit. Polym. J., 23 (1990)299). CPC, R and CSP values calculated on the basis of the theory are in good agreement with the values determined experimentally.     

Dough mixing and breadmaking properties of quinoa-wheat flour blends

Flour blends of quinoa-wheat containing 0, 5, 10, 15, and 20% of manually dehulled quinoa meal or flour were evaluated for dough mixing and breadmaking properties and liking of the bread by a small panel. Increasing amounts of quinoa meal or flour increased farinograph absorption and dislike of bread for most of the panel. Dough development time increased with increase in meal but decreased with increase in quinoa flour. At 10% inclusion levels differences in liking from control 100% wheat flour bread were smaller for flour or water extracted meal to most of the panel, than with 10% non-extracted meal. This suggests that 10% inclusion of flour or water extracted meal may have potential for further investigation.     

Tannins/melamine–urea–formaldehyde (MUF) resins substitution of chrome in leather and its characterization by thermomechanical analysis

A new sulfonated melamine–urea–formaldehyde (MUF) resin of relatively low melamine content, prepared according to a sequential formulation, has been shown to be highly effective when coupled with different natural vegetable tannins to produce leather with the same good characteristics of leather prepared with chrome salts. In particular, the antishrinkage effectiveness of the leather prepared according to the new approach is comparable to that obtained with chrome tanned leathers. The comparison of the traditional leather shrinkage temperatures test method with a new thermomechanical analysis (TMA) test method in tension yields thermograms presenting three major modulus of elasticity (MOE) peaks. These are closely connected to molecular level phenomena determining the shrinkage temperature of leather. The three determining parameters appear to be as follows: (1) The average value of the temperatures at which the three MOE peaks occur: the higher the value of this average, the lower is the shrinkage of leather. (2) The average of maximum MOE values of the TMA peaks: the higher this average is, the better is the leather in regard to antishrinkage effectiveness. This means the leather maximum MOE at each peak is a measure of the resistance to the contraction force induced by heat. (3) The relative intensity of the first TMA peak in relation to the second: the higher the value of the MOE for the first TMA peak is in relation to the second peak, the lower the leather shrinkage appears to be. However, it has not been possible to better define or quantify this latter effect. This new TMA test method in tension has also yielded a mathematical relationship correlating the thermogram peak temperatures and MOE averages with the traditional shrinkage temperature to a high degree of confidence. A previous TMA test method, in compression, has proven to yield more problematic and finally not very reliable results when one needs to apply it to a wide variety of different cases. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 88: 1889–1903, 2003     

焦炉装煤烟尘治理的烟气量计算

通过对焦炉装煤烟尘治理的烟气量计算和研究,提出不同治理系统的烟气量计算方法及应采取的措施。